Author |
Message |
SOADweskey
No More 2.3L
Joined: Tue May 22, 2007 7:36 pm Posts: 4412 Location: Jacksonville, FL
|
Re: Do i really need a bottom end rebuild
^^^^^^ I seen it, that thing sounded like hell but it still ran.
_________________ Boost Creep is your turbo's way of calling you a little bitch for not running enough boost.
452 AWHP 446 lb ft of torque e85 FTW!!
"They are cool manly men now those DSM owners. Before it was just pasty white nerds, metro hair Asian kids and fruit pickers. They do real car club stuff and everything. Sometimes they even spend money here :-/"
-Mike W
|
Mon Sep 26, 2011 7:09 am |
|
|
-red97rum-
Senior Member
Joined: Mon Aug 10, 2009 9:57 am Posts: 1077 Location: Ontario, CA [IE]
|
Re: Do i really need a bottom end rebuild
Yep, that sure sounds like you killed the motor. Either have your mechanic rebuild that 7 bolt or what I would do is find a cheap 6 bolt to swap in there. Either way, good luck with it and let us know how it goes.
_________________-Dustin 1992 Tsi Auto Swapped 10.67@126mph
|
Mon Sep 26, 2011 9:35 am |
|
|
dsmchevyguy
DSM Regular
Joined: Mon Sep 12, 2011 11:16 pm Posts: 252 Location: Gardena
|
Re: Do i really need a bottom end rebuild
I talked to Sam, he said that knock could be jumped timing and bent valves anyone agree?
|
Mon Sep 26, 2011 11:32 am |
|
|
christ
Goderator
Joined: Mon Jan 01, 1979 5:00 am Posts: 5739 Location: D-Town
|
Re: Do i really need a bottom end rebuild
I agree that you're not going to figure it out by asking questions instead of opening it up and finding out what is actually damaged.
_________________ it is physically impossible to open your mouth and tilt your head back and forth at the same time.
|
Mon Sep 26, 2011 11:52 am |
|
|
dsmchevyguy
DSM Regular
Joined: Mon Sep 12, 2011 11:16 pm Posts: 252 Location: Gardena
|
Re: Do i really need a bottom end rebuild
doing that today i'm praying for good news well... better news cause the fact of spending money is not usually good
|
Mon Sep 26, 2011 12:02 pm |
|
|
-red97rum-
Senior Member
Joined: Mon Aug 10, 2009 9:57 am Posts: 1077 Location: Ontario, CA [IE]
|
Re: Do i really need a bottom end rebuild
_________________-Dustin 1992 Tsi Auto Swapped 10.67@126mph
|
Mon Sep 26, 2011 12:30 pm |
|
|
clockworktoy
Squish Face
Joined: Tue May 22, 2007 7:08 pm Posts: 4327 Location: LBC
|
Re: Do i really need a bottom end rebuild
You called the shop earlier today and spoke to me. Did you every check timing? That will tell you if it's valves making love or not. If that checks out fine then it's dead bearings. Sounds like that's the case to me.
|
Mon Sep 26, 2011 8:22 pm |
|
|
dsmchevyguy
DSM Regular
Joined: Mon Sep 12, 2011 11:16 pm Posts: 252 Location: Gardena
|
Re: Do i really need a bottom end rebuild
hey how much would it run to replace those?
|
Mon Sep 26, 2011 10:39 pm |
|
|
Synthetek
Luvz teh Beer!!
Joined: Tue May 22, 2007 6:46 pm Posts: 2848 Location: La Palma, OC
|
Re: Do i really need a bottom end rebuild
_________________99 GSX - 296.5 AWHP
I'm assuming you all have guns and crack!
|
Tue Sep 27, 2011 1:47 am |
|
|
-red97rum-
Senior Member
Joined: Mon Aug 10, 2009 9:57 am Posts: 1077 Location: Ontario, CA [IE]
|
Re: Do i really need a bottom end rebuild
_________________-Dustin 1992 Tsi Auto Swapped 10.67@126mph
|
Tue Sep 27, 2011 9:07 am |
|
|
dsmchevyguy
DSM Regular
Joined: Mon Sep 12, 2011 11:16 pm Posts: 252 Location: Gardena
|
Re: Do i really need a bottom end rebuild
well i'm going to drop the pan sometime this week and cut open the oil filter for shards and check out the oil for anything terribly wrong like shard of metal there too or even shavings
|
Tue Sep 27, 2011 10:26 am |
|
|
LambdaJoker
Senior Member
Joined: Sun Dec 12, 2010 8:12 am Posts: 518 Location: Pomona
|
Re: Do i really need a bottom end rebuild
Just hope that it's nothing more than bent valves due to skipped timing. It's not that hard to check the timing.
_________________ -Raul aka Jr. 1996 Eclipse GSX 1992 Eclipse GSX (down at the moment) 2003 Yamaha R6
|
Tue Sep 27, 2011 12:27 pm |
|
|
dsmchevyguy
DSM Regular
Joined: Mon Sep 12, 2011 11:16 pm Posts: 252 Location: Gardena
|
Re: Do i really need a bottom end rebuild
ya i just dont have my car with me its in culver city and i live near torrance and the tow was 135 so i gotta go get my car first before i can even do anything
|
Tue Sep 27, 2011 12:34 pm |
|
|
Illeagle
Talon of Doom
Joined: Wed May 23, 2007 10:07 am Posts: 3615 Location: Long Beach
|
Re: Do i really need a bottom end rebuild
bent valves car might not even run if its bent bad enough. Check your timing first and foremost. If its good, drain oil and pan for gold.
_________________1/4 ET-11.657@121.18mph w/ 1.682 60' 445whp/427tq on RRE Dyno All on 91 pump. Do you need your car tooned? Got some extra cash? PM me for details. I offer street and dyno tunes
|
Tue Sep 27, 2011 11:50 pm |
|
|
dsmchevyguy
DSM Regular
Joined: Mon Sep 12, 2011 11:16 pm Posts: 252 Location: Gardena
|
Re: Do i really need a bottom end rebuild
i know i sound like an idiot and this was taken from my phone any ideas?
|
Wed Oct 05, 2011 11:19 pm |
|
|