|
Register •
FAQ
• Search • Login
|
|
|
Page 1 of 1
|
[ 7 posts ] |
|
Clutch wont engage or disengage
Author |
Message |
2dr Evo
DSM Regular
Joined: Fri Nov 27, 2009 9:46 pm Posts: 50 Location: San Clemente
|
Clutch wont engage or disengage
I replaced the clutch, throwout bearing, slave cylinder, master cylinder, and resurfaced the flywheel. After the install of the clutch I drove the car about 150 parked it, then came out the next morning and had the problem with the clutch not wanting to engage or disengage.
As i was taking it back apart i noticed the drivers side axle wasn't in completely, could this have had anything to do with it?
|
Mon Oct 17, 2011 3:14 pm |
|
|
SOADweskey
No More 2.3L
Joined: Tue May 22, 2007 7:36 pm Posts: 4412 Location: Jacksonville, FL
|
Re: Clutch wont engage or disengage
Is the transmission still bolted tightly to the engine?
_________________ Boost Creep is your turbo's way of calling you a little bitch for not running enough boost.
452 AWHP 446 lb ft of torque e85 FTW!!
"They are cool manly men now those DSM owners. Before it was just pasty white nerds, metro hair Asian kids and fruit pickers. They do real car club stuff and everything. Sometimes they even spend money here :-/"
-Mike W
|
Mon Oct 17, 2011 3:44 pm |
|
|
christ
Goderator
Joined: Mon Jan 01, 1979 5:00 am Posts: 5739 Location: D-Town
|
Re: Clutch wont engage or disengage
Go under the car and push the fork towards the slave cylinder by hand, does the fork move or is there a fluid pressure stopping it? I don't see you changed the fulcrum ball. That should be on your list of to do's every change. Also, how does your clutch fluid level look?
_________________ it is physically impossible to open your mouth and tilt your head back and forth at the same time.
|
Mon Oct 17, 2011 3:54 pm |
|
|
2dr Evo
DSM Regular
Joined: Fri Nov 27, 2009 9:46 pm Posts: 50 Location: San Clemente
|
Re: Clutch wont engage or disengage
No i have removed the transmission from the car. There was pressure in the clutch pedal all the way to the floor, just felt like it wasn't catching. Clutch fluid was good. Neither fulcrum ball or clutch fork were replaced.
|
Mon Oct 17, 2011 5:48 pm |
|
|
805dsmALEX
Senior Member
Joined: Tue May 22, 2007 7:22 pm Posts: 689 Location: Oxnard Shores
|
Re: Clutch wont engage or disengage
Did u Bleed the clutch and adjusted the master cyl?
_________________3kgt VR4
|
Mon Oct 17, 2011 6:10 pm |
|
|
2dr Evo
DSM Regular
Joined: Fri Nov 27, 2009 9:46 pm Posts: 50 Location: San Clemente
|
Re: Clutch wont engage or disengage
Yes i did both of those. When i was researching i read that if the axle isn't in all the way that could cause these problems, is that true? I forgot to mention its a 95 Talon awd.
|
Mon Oct 17, 2011 6:55 pm |
|
|
christ
Goderator
Joined: Mon Jan 01, 1979 5:00 am Posts: 5739 Location: D-Town
|
Re: Clutch wont engage or disengage
youll have bigger problems than that if you didnt put your passanger axle in all the way.
_________________ it is physically impossible to open your mouth and tilt your head back and forth at the same time.
|
Mon Oct 17, 2011 9:10 pm |
|
|
|
Page 1 of 1
|
[ 7 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 17 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum
|
|
|
|