 |
|
Page 1 of 1
|
[ 10 posts ] |
|
| Author |
Message |
|
So_CalXDSM
Post Master
Joined: Thu Jan 28, 2010 2:51 pm
Posts: 611
Location: Oxnard,CA
|
 How to install a BSEK? Ive never seen a thread on how to do this?
How exactly is it done on a 6 bolt oil pump?
_________________
///BBR Tuned
|
| Mon Aug 16, 2010 9:23 pm |
|
|
|
805dsmALEX
Senior Member
Joined: Tue May 22, 2007 7:22 pm
Posts: 689
Location: Oxnard Shores
|
Re: How to install a BSEK? _________________3kgt VR4
|
| Mon Aug 16, 2010 11:07 pm |
|
|
|
So_CalXDSM
Post Master
Joined: Thu Jan 28, 2010 2:51 pm
Posts: 611
Location: Oxnard,CA
|
Re: How to install a BSEK? Damn!
That shit looks like a mission!
_________________
///BBR Tuned
|
| Tue Aug 17, 2010 12:04 am |
|
|
|
fmedgsx
DSM Regular
Joined: Sun Dec 20, 2009 6:48 pm
Posts: 267
Location: san diego the whales vagina
|
Re: How to install a BSEK? its one of things that are easier said than done.
_________________
Kris Albee
1997 pearl grey gsx project Holly Wood
1991 tsi awd stock bottom end w/ 2g head, kiggly springs, HKS 272's, RC1200's, shep4, QM twin, fp manifold, full megan exhaust, hx35 in bep housing, ets 4" fmic, BJ'sSMIM, Tial bov, tial 41mm, v3 ecmlink SD, 30psi, E85, 99 problems and this Bitch is one
|
| Tue Aug 17, 2010 12:32 am |
|
|
|
DSM99
Moderator
Joined: Fri May 25, 2007 11:51 am
Posts: 3373
Location: The Bat-Cave
|
Re: How to install a BSEK? Thats something way easier to do when the engine is out of the car. IMO it's not even worth the hassel to do it unless the motor is out.
|
| Tue Aug 17, 2010 11:37 am |
|
|
|
clockworktoy
Squish Face
Joined: Tue May 22, 2007 7:08 pm
Posts: 4327
Location: LBC
|
Re: How to install a BSEK? Are you building a motor? Are you balancing the rotating assembly? If no then don't do this mod. Its a PIA, and if you ask its already way over your head. Believe me its not worth the time and effort to do.
|
| Tue Aug 17, 2010 7:23 pm |
|
|
|
So_CalXDSM
Post Master
Joined: Thu Jan 28, 2010 2:51 pm
Posts: 611
Location: Oxnard,CA
|
Re: How to install a BSEK? Yes i am rebuilding a 6 bolt which is why i want to do this since the engine is gonna be worked on outside the chasis.
And depending on my economic status in a couple weeks i might balance the assembly.
How much is a basic balance? Average?
_________________
///BBR Tuned
|
| Tue Aug 17, 2010 10:59 pm |
|
|
|
fmedgsx
DSM Regular
Joined: Sun Dec 20, 2009 6:48 pm
Posts: 267
Location: san diego the whales vagina
|
Re: How to install a BSEK? It all depends on how far you are taking the balancing weither you are including the flywheel, the crank pulley and the rotating assembly. if you are just doing the rotating assembly then it should only run a couple hundred bucks
_________________
Kris Albee
1997 pearl grey gsx project Holly Wood
1991 tsi awd stock bottom end w/ 2g head, kiggly springs, HKS 272's, RC1200's, shep4, QM twin, fp manifold, full megan exhaust, hx35 in bep housing, ets 4" fmic, BJ'sSMIM, Tial bov, tial 41mm, v3 ecmlink SD, 30psi, E85, 99 problems and this Bitch is one
|
| Wed Aug 18, 2010 1:31 am |
|
|
|
So_CalXDSM
Post Master
Joined: Thu Jan 28, 2010 2:51 pm
Posts: 611
Location: Oxnard,CA
|
Re: How to install a BSEK? Is there stages to balance an assembly?
_________________
///BBR Tuned
|
| Wed Aug 18, 2010 9:04 am |
|
|
|
fmedgsx
DSM Regular
Joined: Sun Dec 20, 2009 6:48 pm
Posts: 267
Location: san diego the whales vagina
|
Re: How to install a BSEK? No I dont think there ever should have been "stages" for performance parts because one persons stage is different than another and the stages tell us nothing about the product. most of the time depending on your goals people just balance the rotating assembly. but do not balance the clutch with it if anything only do the flywheel and pulley with the rotating assembly.
_________________
Kris Albee
1997 pearl grey gsx project Holly Wood
1991 tsi awd stock bottom end w/ 2g head, kiggly springs, HKS 272's, RC1200's, shep4, QM twin, fp manifold, full megan exhaust, hx35 in bep housing, ets 4" fmic, BJ'sSMIM, Tial bov, tial 41mm, v3 ecmlink SD, 30psi, E85, 99 problems and this Bitch is one
|
| Wed Aug 18, 2010 12:03 pm |
|
|
|
|
Page 1 of 1
|
[ 10 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 42 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
|
|
 |
|
