|
Register •
FAQ
• Search • Login
|
|
|
Page 1 of 1
|
[ 7 posts ] |
|
Author |
Message |
twisted metal
Senior Member
Joined: Sat Dec 22, 2007 2:38 am Posts: 921 Location: Las Vegas
|
oil feed from head seal
Ok so I feed my turbo from the filter housing and seal the head feed spot with a bolt. Now I broke the bolt off in the head and its one of the oil feed bolts that are hollow so I'm gonna shoot oil everwhere. Now I don't have a way to remove the broken bolt without driving the car somwhere. How should I seal the hole?
_________________ 73 plymouth duster 360 91 talon tsi awd (rip) 91 eclipse gsT. (Rip)
|
Wed May 27, 2009 6:11 pm |
|
|
4GRIDER
BANNED 4 LIFE!
Joined: Thu Apr 17, 2008 5:48 pm Posts: 973 Location: San Fernando Valley
|
Re: oil feed from head seal
J-B WELD
_________________|DIAMOND-STAR-MOTORS||4G63T_RACING|
|
Wed May 27, 2009 6:19 pm |
|
|
twisted metal
Senior Member
Joined: Sat Dec 22, 2007 2:38 am Posts: 921 Location: Las Vegas
|
Re: oil feed from head seal
That was my first though I just don't know if it will handle the pressure and I also need to know if I can just seal it or does oil need to flow through there. Only reason I think that is because its a banjo bolt (I'm not sure if that's what its called) my other thought was to hammer a nail in there then use the jbweld over the head of the nail.
_________________ 73 plymouth duster 360 91 talon tsi awd (rip) 91 eclipse gsT. (Rip)
|
Wed May 27, 2009 6:51 pm |
|
|
gordonbradford
DSM Regular
Joined: Fri Jan 09, 2009 11:45 am Posts: 325 Location: Phoenix, AZ
|
Re: oil feed from head seal
You can just jb weld it. But if it was me i would use an easy out and just put a new bolt in.
|
Wed May 27, 2009 7:40 pm |
|
|
4GRIDER
BANNED 4 LIFE!
Joined: Thu Apr 17, 2008 5:48 pm Posts: 973 Location: San Fernando Valley
|
Re: oil feed from head seal
Yea tru taking the old be better could get worst, and get particals inside your head
_________________|DIAMOND-STAR-MOTORS||4G63T_RACING|
|
Wed May 27, 2009 7:52 pm |
|
|
Erix
Senior Member
Joined: Tue May 22, 2007 7:10 pm Posts: 4767 Location: 818
|
Re: oil feed from head seal
screw in another thinner bolt into the hole in the banjo bolt
_________________ Current: '97 GS-T Spyder Past: '90 2.0L GS Turbo, '98 GS-T Spyder, '90 1.8L GS
|
Thu May 28, 2009 12:43 am |
|
|
gordonbradford
DSM Regular
Joined: Fri Jan 09, 2009 11:45 am Posts: 325 Location: Phoenix, AZ
|
Re: oil feed from head seal
|
Thu May 28, 2009 1:10 am |
|
|
|
Page 1 of 1
|
[ 7 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 18 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum
|
|
|
|