Author |
Message |
twisted metal
Senior Member
Joined: Sat Dec 22, 2007 2:38 am Posts: 921 Location: Las Vegas
|
delema
So I lost my keys....again (for those who remember the fwd hahah) and my stering wheel is locked and I can't remember how to take the key cylinder off so I can block the piece from locking my steering wheel. I've looked in the manual and it says I need a key but I know there's a way to do it without because I've done it before.
_________________ 73 plymouth duster 360 91 talon tsi awd (rip) 91 eclipse gsT. (Rip)
|
Fri Mar 13, 2009 11:42 am |
|
|
amskater
Official Photographer
Joined: Wed May 23, 2007 5:00 am Posts: 3726 Location: 626
|
Re: delema
not sure how long it takes but you might be able to order a key from a mitsu dealership
|
Fri Mar 13, 2009 12:23 pm |
|
|
twisted metal
Senior Member
Joined: Sat Dec 22, 2007 2:38 am Posts: 921 Location: Las Vegas
|
Re: delema
Any idea on how much they cost?
_________________ 73 plymouth duster 360 91 talon tsi awd (rip) 91 eclipse gsT. (Rip)
|
Fri Mar 13, 2009 12:37 pm |
|
|
amskater
Official Photographer
Joined: Wed May 23, 2007 5:00 am Posts: 3726 Location: 626
|
Re: delema
I dont think its that much I need to order one too my copy of a copy sucks
|
Fri Mar 13, 2009 12:40 pm |
|
|
clockworktoy
Squish Face
Joined: Tue May 22, 2007 7:08 pm Posts: 4327 Location: LBC
|
Re: delema
Blank key from them is $15 and im not sure how much they would charge you to cut it. Word of advice, last time i went and asked about this they said they weren't sure if it would work..
|
Fri Mar 13, 2009 6:03 pm |
|
|
twisted metal
Senior Member
Joined: Sat Dec 22, 2007 2:38 am Posts: 921 Location: Las Vegas
|
Re: delema
As long as the key will work for my doors ill be happy
_________________ 73 plymouth duster 360 91 talon tsi awd (rip) 91 eclipse gsT. (Rip)
|
Fri Mar 13, 2009 6:29 pm |
|
|
Erix
Senior Member
Joined: Tue May 22, 2007 7:10 pm Posts: 4767 Location: 818
|
Re: delema
should work on 1g's since our OEM keys dont have any special 'chips' in them like newer cars that require them for the car to start or operate.
they should be able to cut the key for your car and it should work fine.
_________________ Current: '97 GS-T Spyder Past: '90 2.0L GS Turbo, '98 GS-T Spyder, '90 1.8L GS
|
Fri Mar 13, 2009 8:19 pm |
|
|
Boost_Addict_88
McFly
Joined: Tue Sep 30, 2008 12:19 am Posts: 701 Location: Downey/Bellflower/Fullerton, Ca
|
Re: delema
If you have the key number then you could go to Ace Hardware and have one made.
|
Sat Mar 14, 2009 12:01 pm |
|
|
ghetto_bird
The Don!
Joined: Sat Sep 15, 2007 9:18 pm Posts: 1113 Location: south el monte
|
Re: delema
|
Mon Mar 16, 2009 11:17 am |
|
|
christ
Goderator
Joined: Mon Jan 01, 1979 5:00 am Posts: 5739 Location: D-Town
|
Re: delema
_________________ it is physically impossible to open your mouth and tilt your head back and forth at the same time.
|
Mon Mar 16, 2009 11:29 am |
|
|
twisted metal
Senior Member
Joined: Sat Dec 22, 2007 2:38 am Posts: 921 Location: Las Vegas
|
Re: delema
Yea ima hit up mitsu and see if they can cut me one
_________________ 73 plymouth duster 360 91 talon tsi awd (rip) 91 eclipse gsT. (Rip)
|
Mon Mar 16, 2009 8:47 pm |
|
|