ladsm.com http://www.ladsm.com/forum/ |
|
1g. Wire tuck and nhra battery relocation http://www.ladsm.com/forum/viewtopic.php?f=4&t=15105 |
Page 2 of 2 |
Author: | slidesidwayz [ Fri Mar 08, 2013 12:00 pm ] |
Post subject: | Re: 1g. Wire tuck and nhra battery relocation |
Looks sick Gabe |
Author: | LOLVTEC [ Fri Mar 08, 2013 12:43 pm ] |
Post subject: | Re: 1g. Wire tuck and nhra battery relocation |
Thanks guys. Hopefully it turns on lol Sent from my LG-P999 using Tapatalk 2 |
Author: | slidesidwayz [ Tue Nov 05, 2013 5:01 pm ] |
Post subject: | Re: 1g. Wire tuck and nhra battery relocation |
What sensors did you end up using for your wire tuck? |
Author: | LOLVTEC [ Thu Nov 07, 2013 12:02 pm ] |
Post subject: | Re: 1g. Wire tuck and nhra battery relocation |
I just took out the harness and measured every wire. Just cut the unused wires, heat shrink it. And hide it, Sensor wise, tps, isc, cas, ignition, coil pack, injectors, knock, resistor, maf, just the necessary things to run. Deleted everything. If I have to add something I'll splice in straight from the pigtail of the ecu. You have to examine the wires individually because some of them share the same ground and some of them are connected with each other. Took me about 8 hours total. A ton of heat shrink. Soldering (use flux) and f6 braided Sent from my SGH-M919 using Tapatalk 2 |
Author: | slidesidwayz [ Thu Nov 07, 2013 2:25 pm ] |
Post subject: | Re: 1g. Wire tuck and nhra battery relocation |
Where did you order your braid from? On a side note: do you have a tps pigtail If you run speed density would you just wire that instead of Maf or would you leave the maf wires there incase you wanted to switch back? |
Author: | slidesidwayz [ Thu Nov 07, 2013 2:30 pm ] |
Post subject: | Re: 1g. Wire tuck and nhra battery relocation |
Also, what size did you use for the braid? |
Author: | LOLVTEC [ Thu Nov 07, 2013 3:02 pm ] |
Post subject: | Re: 1g. Wire tuck and nhra battery relocation |
No tps pigtail. And I have the plug and play harness for sd I just shortened the maf wires Sent from my SGH-M919 using Tapatalk 2 |
Author: | LOLVTEC [ Thu Nov 07, 2013 3:04 pm ] |
Post subject: | Re: 1g. Wire tuck and nhra battery relocation |
Also have a. Little note book and write down your new harness. What wires are which Sent from my SGH-M919 using Tapatalk 2 |
Author: | slidesidwayz [ Thu Nov 07, 2013 4:29 pm ] |
Post subject: | Re: 1g. Wire tuck and nhra battery relocation |
Cool thanks. I have most of what I need to do it. I just need to order the pins. |
Author: | slidesidwayz [ Thu Nov 07, 2013 4:32 pm ] |
Post subject: | Re: 1g. Wire tuck and nhra battery relocation |
can the tps be grounded to the chassis or does it need to go back to the ecu as a sensor ground? |
Author: | slidesidwayz [ Thu Nov 07, 2013 4:58 pm ] |
Post subject: | Re: 1g. Wire tuck and nhra battery relocation |
Do you still have all the lengths of the wires that you recorded? |
Author: | LOLVTEC [ Thu Nov 07, 2013 5:19 pm ] |
Post subject: | Re: 1g. Wire tuck and nhra battery relocation |
It depends on where you place your stuff. And where you want the harness to come out. A real wire tuck is you put the harness near the shifter cable. You drill a hole, that's why you have to shorten everything. Plus I can mine about 4 inches of way just in case and its tucked in the dash side. Dsm is not a daily so I took my time cause if you mess up you have to do it all over again! Sent from my SGH-M919 using Tapatalk 2 |
Page 2 of 2 | All times are UTC - 8 hours [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |