| ladsm.com http://www.ladsm.com/forum/ |
|
| FMIC piping in the way of my bumper http://www.ladsm.com/forum/viewtopic.php?f=4&t=14389 |
Page 1 of 1 |
| Author: | slidesidwayz [ Fri Apr 27, 2012 2:45 pm ] |
| Post subject: | FMIC piping in the way of my bumper |
Has anyone used a FMIC kit like this before. I bought a 1g with this on it and cannot figure out how to mount the front bumper  . It looks like I would need to cut alot out of the bumper. Is there a way to use the excess piping to make a short route setup? What should I do?Thanks  |
|
| Author: | 805dsmALEX [ Fri Apr 27, 2012 3:07 pm ] |
| Post subject: | Re: FMIC piping in the way of my bumper |
If u have a saw saw or anything to cut the pipes and some couplers u can modify it.. I did my own on my old 1g, same core . U can get it around towards the oil filter but you'll have to cut the Tow Hook off , other than that and a new "J" pipe that faces the driverside and you'll be good to go. 
|
|
| Author: | slidesidwayz [ Sat Apr 28, 2012 10:58 pm ] |
| Post subject: | Re: FMIC piping in the way of my bumper |
I guess ill start with buying a jpipe and a saw  Thanks for your help..
|
|
| Author: | ghetto_bird [ Tue May 15, 2012 9:09 pm ] |
| Post subject: | Re: FMIC piping in the way of my bumper |
THAT'S A SHIT LOAD OF PLUMBING!!!!! fuck that short rout all the way... i have 3 pipes 1 coupler, 2 90* elbow. and the 2 end tank couplers. (done) if you can cut and fit. i made my IC for less or about 100 bucks with a 3 in core (25 in by 13 in by 3 in). i'm not worried about cooling since i run meth all the time.. |
|
| Author: | christ [ Thu May 17, 2012 8:21 am ] |
| Post subject: | Re: FMIC piping in the way of my bumper |
Make a stripper pole out of it. |
|
| Author: | twisted metal [ Wed May 30, 2012 11:41 am ] |
| Post subject: | Re: FMIC piping in the way of my bumper |
is there a dead guy in the table? |
|
| Author: | BoostCreep [ Tue Jun 05, 2012 5:48 pm ] |
| Post subject: | Re: FMIC piping in the way of my bumper |
That is a hilarious amount of piping. If someone wants to use the factory SMIC piping hole that badly, at least buy a FMIC that has the inlet and outlet on the same side. |
|
| Author: | slidesidwayz [ Sat Jun 09, 2012 5:28 pm ] |
| Post subject: | FMIC piping in the way of my bumper |
| Author: | slidesidwayz [ Sat Jun 09, 2012 5:29 pm ] |
| Post subject: | FMIC piping in the way of my bumper |
| Author: | slidesidwayz [ Mon Jun 11, 2012 9:18 am ] |
| Post subject: | Re: FMIC piping in the way of my bumper |
| Author: | str8bsting [ Mon Jun 11, 2012 10:01 am ] |
| Post subject: | FMIC piping in the way of my bumper |
What size couplers do u need? I might have a few. |
|
| Author: | slidesidwayz [ Mon Jun 11, 2012 12:12 pm ] |
| Post subject: | Re: FMIC piping in the way of my bumper |
My piping is 2.5 inches. If someone can help me make this a short route, I have another fmic that I will never use that you can have
|
|
| Page 1 of 1 | All times are UTC - 8 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|