Author |
Message |
slidesidwayz
DSM Regular
Joined: Mon Mar 14, 2011 10:42 pm Posts: 398 Location: Woodland Hills
|
FMIC piping in the way of my bumper
Has anyone used a FMIC kit like this before. I bought a 1g with this on it and cannot figure out how to mount the front bumper . It looks like I would need to cut alot out of the bumper. Is there a way to use the excess piping to make a short route setup? What should I do? Thanks
|
Fri Apr 27, 2012 2:45 pm |
|
|
805dsmALEX
Senior Member
Joined: Tue May 22, 2007 7:22 pm Posts: 689 Location: Oxnard Shores
|
Re: FMIC piping in the way of my bumper
If u have a saw saw or anything to cut the pipes and some couplers u can modify it.. I did my own on my old 1g, same core . U can get it around towards the oil filter but you'll have to cut the Tow Hook off , other than that and a new "J" pipe that faces the driverside and you'll be good to go.
_________________3kgt VR4
|
Fri Apr 27, 2012 3:07 pm |
|
|
slidesidwayz
DSM Regular
Joined: Mon Mar 14, 2011 10:42 pm Posts: 398 Location: Woodland Hills
|
Re: FMIC piping in the way of my bumper
I guess ill start with buying a jpipe and a saw Thanks for your help..
|
Sat Apr 28, 2012 10:58 pm |
|
|
ghetto_bird
The Don!
Joined: Sat Sep 15, 2007 9:18 pm Posts: 1113 Location: south el monte
|
Re: FMIC piping in the way of my bumper
THAT'S A SHIT LOAD OF PLUMBING!!!!! fuck that short rout all the way...
i have 3 pipes 1 coupler, 2 90* elbow. and the 2 end tank couplers. (done) if you can cut and fit. i made my IC for less or about 100 bucks with a 3 in core (25 in by 13 in by 3 in). i'm not worried about cooling since i run meth all the time..
|
Tue May 15, 2012 9:09 pm |
|
|
christ
Goderator
Joined: Mon Jan 01, 1979 5:00 am Posts: 5739 Location: D-Town
|
Re: FMIC piping in the way of my bumper
Make a stripper pole out of it.
_________________ it is physically impossible to open your mouth and tilt your head back and forth at the same time.
|
Thu May 17, 2012 8:21 am |
|
|
twisted metal
Senior Member
Joined: Sat Dec 22, 2007 2:38 am Posts: 921 Location: Las Vegas
|
Re: FMIC piping in the way of my bumper
is there a dead guy in the table?
_________________ 73 plymouth duster 360 91 talon tsi awd (rip) 91 eclipse gsT. (Rip)
|
Wed May 30, 2012 11:41 am |
|
|
BoostCreep
DSM Regular
Joined: Wed Dec 01, 2010 2:37 am Posts: 98 Location: Los Angeles, CA
|
Re: FMIC piping in the way of my bumper
That is a hilarious amount of piping. If someone wants to use the factory SMIC piping hole that badly, at least buy a FMIC that has the inlet and outlet on the same side.
_________________
|
Tue Jun 05, 2012 5:48 pm |
|
|
slidesidwayz
DSM Regular
Joined: Mon Mar 14, 2011 10:42 pm Posts: 398 Location: Woodland Hills
|
FMIC piping in the way of my bumper
|
Sat Jun 09, 2012 5:28 pm |
|
|
slidesidwayz
DSM Regular
Joined: Mon Mar 14, 2011 10:42 pm Posts: 398 Location: Woodland Hills
|
FMIC piping in the way of my bumper
|
Sat Jun 09, 2012 5:29 pm |
|
|
slidesidwayz
DSM Regular
Joined: Mon Mar 14, 2011 10:42 pm Posts: 398 Location: Woodland Hills
|
Re: FMIC piping in the way of my bumper
|
Mon Jun 11, 2012 9:18 am |
|
|
str8bsting
DSM Regular
Joined: Tue Nov 17, 2009 9:43 am Posts: 88
|
FMIC piping in the way of my bumper
What size couplers do u need? I might have a few.
|
Mon Jun 11, 2012 10:01 am |
|
|
slidesidwayz
DSM Regular
Joined: Mon Mar 14, 2011 10:42 pm Posts: 398 Location: Woodland Hills
|
Re: FMIC piping in the way of my bumper
My piping is 2.5 inches. If someone can help me make this a short route, I have another fmic that I will never use that you can have
|
Mon Jun 11, 2012 12:12 pm |
|
|