| ladsm.com http://www.ladsm.com/forum/ |
|
| BOV opinions http://www.ladsm.com/forum/viewtopic.php?f=26&t=8579 |
Page 1 of 1 |
| Author: | jstoned1 [ Thu Mar 19, 2009 4:35 pm ] |
| Post subject: | BOV opinions |
well the knock off greddy type s that came with my fmic kit is leaking so im looking for a bov in the same size range (hood clearance) and i heard greddy lost manufacturing exclusivity on the type s. anyhow i was looking at the greddy type R and the type rs. not sure on the type R the pic looks like it would recirc, but dont know if the outlet is too big.. any suggestions? i plan on running up to 25 psi and my uicp is already flanged for greddy and stock 1g. is there a better bov im missing? |
|
| Author: | christ [ Thu Mar 19, 2009 5:34 pm ] |
| Post subject: | Re: BOV opinions |
Type S' give me a hardon. I'd always use a Type S, personally. |
|
| Author: | Illeagle [ Thu Mar 19, 2009 5:47 pm ] |
| Post subject: | Re: BOV opinions |
Modded 1G. Will hold 30+ PSi, cheap. You want cute, go greddy S or RS |
|
| Author: | jstoned1 [ Thu Mar 19, 2009 7:44 pm ] |
| Post subject: | Re: BOV opinions |
yeah greddys are nice looking units for sure. but i like cheap alot better! i have heard of crushing them, did a little looking around and found the dodge garage mod too. you think i could get away with just crushing it? |
|
| Author: | clockworktoy [ Thu Mar 19, 2009 8:15 pm ] |
| Post subject: | Re: BOV opinions |
The 1g bov is a good option, and the RS is roughly the same size as the type S so that could also be a direct replacement. |
|
| Author: | Illeagle [ Fri Mar 20, 2009 9:16 am ] |
| Post subject: | Re: BOV opinions |
the dodge garage mod is really easy. Don't need to go as far as drilling and tapping for a set screw. You could get away with filling the lower hole with JB weld and drilling a hole in the side to so the diaphram could move, otherwise it will create a vacuum underneath it and not allow the valve to move (like running no bov) you don't have to put a nipple on the side to make it quick release. After doing the mod it will be the same as an unadjustable TypeRS by design. |
|
| Author: | jstoned1 [ Fri Mar 20, 2009 12:12 pm ] |
| Post subject: | Re: BOV opinions |
| Author: | Infinite_KaoS [ Fri Mar 20, 2009 12:25 pm ] |
| Post subject: | Re: BOV opinions |
Don't worry if you fuck it up, you always have one over here. Granted your not counting this one as your only 1. |
|
| Author: | jstoned1 [ Fri Mar 20, 2009 12:37 pm ] |
| Post subject: | Re: BOV opinions |
| Author: | Illeagle [ Fri Mar 20, 2009 1:22 pm ] |
| Post subject: | Re: BOV opinions |
doesn't matter where you drill, so long as it intersects the old port. |
|
| Author: | jstoned1 [ Fri Mar 20, 2009 1:33 pm ] |
| Post subject: | Re: BOV opinions |
| Page 1 of 1 | All times are UTC - 8 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|