| ladsm.com http://www.ladsm.com/forum/ |
|
| clutch/tranny question http://www.ladsm.com/forum/viewtopic.php?f=26&t=4612 |
Page 1 of 2 |
| Author: | twisted metal [ Mon Jul 21, 2008 1:33 pm ] |
| Post subject: | clutch/tranny question |
| Author: | turboawdfanatic [ Mon Jul 21, 2008 4:07 pm ] |
| Post subject: | |
Probably air in the hydraulics. Bleed and re-bleed using this method: Get a helper Put a hose on the slave bleeder, put the other end in a bottle w/ some fluid Keep that end in the fluid the whole time Have helper pump the pedal once then hold it down to the floor Crack the bleeder open, watch fluid & bubbles come out, close bleeder Have helper *slowly* lift pedal off floor (it will stay on the floor after you crack the bleeder) Repeat the above steps, check your master every 3 or 4 times and make sure it NEVER gets below the "min" line or you'll get air in the system. THEN (this is very important): Crack the bleeder open and push the fork arm back towards the slave. W/ the bleeder open, have the helper push the pedal to the floor again. Then close the bleeder. This removes air from the slave itself. You can repeat this a few times if you want. to help you out. Once this is done, adjust your clutch pedal via instructions on the VFAQ and . While you're at it, check your clutch pedal for wear (near bottom of RRE link). BTW, did you replace the fork/ball and throw out bearing when you did the swap? A worn fork/ball can lead to poor disengagement too. |
|
| Author: | twisted metal [ Mon Jul 21, 2008 4:42 pm ] |
| Post subject: | |
| Author: | turboawdfanatic [ Tue Jul 22, 2008 2:09 am ] |
| Post subject: | |
| Author: | twisted metal [ Tue Jul 22, 2008 10:21 am ] |
| Post subject: | |
Wasn't able too bleed it lastnight but I'm gonna try today if I can find someone too come help |
|
| Author: | turboawdfanatic [ Tue Jul 22, 2008 11:46 am ] |
| Post subject: | |
Forgot to mention about the clutch dragging test: Put car on level surface Make sure e-brake is off Put in 1st gear Hold clutch to the floor Rev engine The car should roll forward at about 7200rpm. If it rolls forward before 7200rpm the clutch is dragging. |
|
| Author: | twisted metal [ Tue Jul 22, 2008 1:10 pm ] |
| Post subject: | |
Hmmm ill check that I think it rolls after 7200 when its in netural I hear a kinda scratchy sound comming from the tranny and when I push the clutch in it stops any ideas? I also need too adjust the throttle cable and figure out what this cel is |
|
| Author: | turboawdfanatic [ Tue Jul 22, 2008 4:22 pm ] |
| Post subject: | |
| Author: | twisted metal [ Tue Jul 22, 2008 5:14 pm ] |
| Post subject: | |
| Author: | turboawdfanatic [ Tue Jul 22, 2008 5:31 pm ] |
| Post subject: | |
| Author: | twisted metal [ Tue Jul 22, 2008 6:00 pm ] |
| Post subject: | |
| Author: | 4GRIDER [ Tue Jul 22, 2008 6:02 pm ] |
| Post subject: | |
| Author: | turboawdfanatic [ Tue Jul 22, 2008 6:06 pm ] |
| Post subject: | |
| Author: | twisted metal [ Tue Jul 22, 2008 6:36 pm ] |
| Post subject: | |
[quote="turboawdfanatic"][quote="jasondqd"]But on that slave how much do u want for it?[/quote] I meant that I have an extra slave boot. I *think* I have an extra slave, but I'm not 100% sure it's good. I'm pretty sure it is though. I'll trade you for the upper power steering hose you were going to sell me.[/quote] Haha sounds good to me I can't find a slave anywhere and I can't wait the week its gonna take too get one if your free anytime could u swing by I'm in fullerton off orangethorp and euclid |
|
| Author: | twisted metal [ Tue Jul 22, 2008 6:38 pm ] |
| Post subject: | |
[quote="4GRIDER"][quote="jasondqd"]Haha when gus got his 6 bolt it came outa an awd and still had the starter plate. So I tradegus some motormount inserts. But on that slave how much do u want for it?[/quote]. do you need any body parts for your talon if so let me know b4 i junk the shell[/quote] what color/year is it? |
|
| Page 1 of 2 | All times are UTC - 8 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|