| ladsm.com http://www.ladsm.com/forum/ |
|
| Welding for tubular manifold http://www.ladsm.com/forum/viewtopic.php?f=26&t=13990 |
Page 1 of 1 |
| Author: | Spyder97 [ Sun Feb 05, 2012 9:51 am ] |
| Post subject: | Welding for tubular manifold |
Hello everyone My tubular manifold has a crack. Can anyone weld/fix it? Its in the middle area where the tubes come together. I had it fixed by a muffler shop but it opened up again. Thanks! |
|
| Author: | rcarbajal4 [ Sun Feb 05, 2012 10:30 am ] |
| Post subject: | Re: Welding for tubular manifold |
I can weld it for you |
|
| Author: | Illeagle [ Thu Feb 09, 2012 6:47 am ] |
| Post subject: | Re: Welding for tubular manifold |
If it's cheap thin wall shit, it will crack again and again and again |
|
| Author: | rcarbajal4 [ Thu Feb 09, 2012 10:00 am ] |
| Post subject: | Re: Welding for tubular manifold |
| Author: | Spyder97 [ Fri Jan 11, 2013 3:06 pm ] |
| Post subject: | Re: Welding for tubular manifold |
Thanks guys for replying. I never got a noticed of the replies. I just saw them. Still need to weld the manifold. Its a turbo performance old school one. Hoping someone can weld it. The muffler shop only welded from the outside and seemed to make the hole bigger.i was told it needs to be weld from the inside but its a bit hard to get to. And might need to be cut open then reweld. If anyone can do it please text me. I can text a picture. Thanks 323-347-9487 |
|
| Author: | LOLVTEC [ Sat Jan 12, 2013 11:31 am ] |
| Post subject: | Re: Welding for tubular manifold |
With all the money your spending.on welding it you can get the same one on ebay lol Sent from my LG-P999 using Tapatalk 2 |
|
| Author: | 4G63KING [ Sat Jan 12, 2013 2:32 pm ] |
| Post subject: | Re: Welding for tubular manifold |
Come to my house n if up this tubular one for 40 |
|
| Author: | Spyder97 [ Sun Jan 13, 2013 10:06 am ] |
| Post subject: | Re: Welding for tubular manifold |
Lolvtech, sadly ive tried finding the same one on ebay with no luck. 4g63king, im not sure if the one you have will fit. My turbo uses the old turbo performance set up with recirculating o2 housing. That lines up right next to the manifold. Ive looked for other manifolds but it seems I would also have to change the o2 and wastegate housing. |
|
| Author: | 4G63KING [ Sun Jan 13, 2013 5:11 pm ] |
| Post subject: | Re: Welding for tubular manifold |
Isn't the o2 housing, separate from the manifold itself? |
|
| Author: | Spyder97 [ Wed Jan 16, 2013 10:21 pm ] |
| Post subject: | Re: Welding for tubular manifold |
4g63king. Yeah they are separate parts. My current setup has the wastegate attached to the o2 housing and recirculates. My problem is that the wastegate comes up and lines up right next to the manifold. and my current manifold allows room for it. Hope this makes sense. But its been easier to fix this manifold than change the whole setup. |
|
| Author: | 4G63KING [ Fri Jan 18, 2013 6:47 pm ] |
| Post subject: | Re: Welding for tubular manifold |
Well in San Fernando there a very good as welder he can fix it for you |
|
| Author: | Spyder97 [ Sat Jan 19, 2013 12:28 pm ] |
| Post subject: | Re: Welding for tubular manifold |
Can you post or pm the guys info. Thanks! |
|
| Author: | 4G63KING [ Thu Jan 24, 2013 7:29 pm ] |
| Post subject: | Re: Welding for tubular manifold |
It's called jc welding on San Fernando rd. in Pacoima |
|
| Page 1 of 1 | All times are UTC - 8 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|